I really like the cart as a better alternative for my purposes (NO noise, easy for anyone, no odor, cheaper too!! ) I figure I have about $3200 invested in the cart as it stands now.and that is a good deal compared to a UTV. (I paid 2000 for the cart.with almost new bats, and about 1200 in the mods). I would do this again. D&D Motor Systems is the premier DC motor manufacturer in the U.S. For small to medium light-weight electric vehicle (EV) conversions.In addition we offer a complete line of U.S. Made speed controllers to go with our high performance EV motors.Kick the oil habit now. It's a lot more practical than you think.
Based on the photos from that site the green Ezgo TXT is a series motor cart. That style etc would be my choice for a hunting conversion. Ezgo also has the most available aftermarket parts to choose from as well as information like manuals available. If this is the cart you choose, we have the wiring diagrams and service manuals for it here.
Converting An Ezgo Series Cart To Sepex Size
PQ48-450 $725.00New Custom Built Motor, Class H Motor Rating, High Performance Brushes, Speed EZ-GO 48 volt DCS Sepex 19 Spline 13.2 HP, Speed 25-31 mph (estimated) and added 50% more torque,.must upgrade controller., flat terrain and a good quality battery pack.Receive a custom stainless steel Plum Quick Xtreme Power ring (size 12 mens only while supplies last) valued at $399.00 free with the purchase of the Killer Bee Package (motor, controller, wire set and HD Solenoid).Killer Bee motor: $605.00 + Shipping charges (see shipping chart for cost). These custom hand built motors usually take 10-20 business days to build from order date. Full credit card payment is required to start the motor build.Note: South Carolina residents add 8% for sales tax.Plum Quick Motors is the World's leader in Golf Cart Performance, we build the most powerful DC Electric motors and we have the World's Fastest Golf Carts to prove it! You need the right components to go with your Custom Built High Performance Motor.If your cart is equipped with a lift kit and taller tires it is recommended that your upgrade to a Higher amp Sepex Controller. We've listed a few different brand controller options below.36/48 volt 500 amp Alltrax XCT Controller for your brand golf cart.
$625.00.36/48 volt 500 amp 1268 Curtis Sepex controller for your brand golf cart. $625.00Complete 2ga. Wire set is required when installing a higher amp controller. Wire Set for your brand golf cart. $250.00Heavy Duty 36 or 48 volt Solenoid and Diode are required when installing a higher amp controller.Heavy Duty 400 amp 36 or 48 volt Solenoid and Diode. $180.00Note: Solenoid MUST be mounted upright!Note: NO Heavy Duty F&R Switch is required on Sepex carts!Note: With certain EZ-Go carts (1994-current) you'll need to make sure your ITS is set properly to insure you receive 100% throttle at full pedal.Note: We like to make sure the plugger rod sticks out around an 1/8' to ensure 100% throttle.To maximize performance replace rear end fluid with high grade synthetic motor oil.Please note: It is a must that you have a good quality battery pack. At Plum Quick Motors we only use the BEST and in our opinion Trojan batteries are the top of the line.Make sure your brakes are not dragging, you should be able to push and pull your cart with the brakes released on flat terrain.
Also, make sure your tires are properly inflated to 25 - 30 psi.Note: Installing your custom built motor:Don’t put a bumper into the motor coupler once you get it back from Plum Quick. The motor has been tested on a dyno machine and if it had a coupler bumper and/or needed a coupler bumper it was tested and determined at that point to use or not. As for installing the motor onto the rear end, wire brush the rear end output spline shaft, you can spray a light coat of white lithium grease and now slide the motor onto the rear spline shaft all the way until the motor housing bumps the rear end housing. Line up and tighten the motor bolts to secure the motor to the rear end housing. Installing a motor with a different speed sensor connection:Note: All of our Custom Built Sepex Motors come with the standard gray triangle speed sensor plug connection. This is the standard plug connection for Club Car IQ carts.
You can buy speed sensor adapters to convert this plug connection to EZ-GO 36/48 volt PDS carts and Yamaha G19. G22 and G29 plug connections, however you can just simply clip the three wires right behind the gray triangle connector, clip the three wires on your speed sensor connector (leaving your wires as long as possible) and use wire connectors to splice your speed sensor connector to the speed sensor on the new motor. Battle brothers mods.